You have no items in your shopping cart.
Porc-A-Fix Rust Transformer is the answer to the reoccurring rust issues with cast iron and steel fixtures. Neutralizes the rust and stops it in its tracks, prevents the rust from spreading and reappearing after the repairs are made. Once the rust is eliminated, Fill-A-Fix or Porc-A-Fix can be used to complete the repair and make any fixture look new again. Sandpaper and brush top applicator included.
This item is shipped directly from our NJ warehouse. Once the factory seal is broken, shelf life is limited due to external factors and cannot be guaranteed. Corrode-A-Fix is intended for a one time use as per the manufacturer, but if stored in ideal conditions further applications may be available.
- Condition: New: A brand-new, unused, unopened, undamaged item in its original packaging
- Product Type: Rust Transformer
- Easy-to-use, fast drying, no-mix ready to apply
- Non-yellowing / High Gloss / No Mixing of Ingredients
Application Instructions: Remove all loose rust using the wire brush or enclosed sandpaper. Make sure the area is clean and dry. Shake bottle for 30 seconds. Apply to rust with enclosed brush applicator. Rust will convert to a black protective film, usually within 30 minutes. Then apply Porc-A-Fix and/or Fill-A-Fix in 4 to 6 hours after application. Use with adequate ventilation. Clean with water.
Each package contains 1/2 ounce (15cc) of rust transformer material, brush top applicator, finishing paper and complete instructions
We recommend using Fill-A-Fix Porcelain Chip Filler - if your repair is a deep chip or gouge.
Please contact us with any questions you may have.
Ensure that the damaged area and surrounding surface are clean and dry - free of dust, dirt, grease, soap residue, wax and cleaners.
Though not necessary, for a stronger bond you can carefully rough up the damaged area with the enclosed finishing paper (220 grit aluminum oxide sandpaper). The small cut of 1" x 3" allows more selective sanding of small repair areas.
For deep chips and gouges, you should first fill them with Fill•A•Fix before using Porc-A-Fix.
Shake the bottle for at least 30 seconds and allow it to sit for at least one minute prior to opening the cap. This will allow excess material on the cap or brush to roll back into the bottle. Open the cap carefully, making sure to wipe off any excess material on the lip of the bottle with a cloth.
Apply in thin layers, allowing at least one hour drying time between coats. The drying time can be decreased to several minutes by using a hand held hair dryer on the coolest setting, held at least one foot away from the repair. Use a back and forth fanning motion with the hair dryer - do not hold it stationary over one area.
Dry for 24 hours after the last layer is applied. If any brush marks remain, or if any debris has settled into the repair, sand very lightly after drying to remove these imperfections. You may use the enclosed 220-grit finishing paper, or use additional paper of similar or finer grit as you deem fit.
Finish. You may first fine-finish the repaired area with 360-600 grit silicon carbide sandpaper to save buffing time. If you do, sand just until the glaze is smooth with the surrounding porcelain, gently to avoid sanding through the glaze. Note: for many minor repairs, sanding after the final coat may not be necessary.
Then buff the repair and surrounding area with a soft cloth and a bit of automotive polishing compound.
For routine cleaning of the repaired area, use a mild liquid abrasive or dishwashing liquid; we recommend this not only for the repaired area, but for the entire fixture. Do not use harsh chemicals or abrasive cleaners on the repaired area. This will reduce the chance of scratches from surface dirt or abrasion.
Import Duties and Clearance Fees are the Responsibility of the Buyer. Our Free Shipping Policy does not apply to International Addresses. All International Orders will be accompanied by a Commercial Invoice that states a description of the goods, the sale price, and the country of origin of the goods.
Please choose your shipping service carefully as USPS First Class International may not have Tracking Information available for all countries. No Items will be replaced or No refunds will be issued on International Shipping, so choosing USPS Priority Mail International is definitely your better choice.
By choosing USPS First Class International as your service you agree to our terms and conditions and will not hold us responsible for loss or damage to the package and items in it.
Please contact us at firstname.lastname@example.org and we would be happy to quote you a shipping rate based on the weight of the items you would like to purchase.